Our Mission: "Efficiently support the thoughtful exchange of knowledge, values and experiences among RV enthusiasts"
 
RV Parts and Accessories by RVupgrades.com
    iRV2.com RV Forum  Hop To Forum Categories  RV LIFE STYLES  Hop To Forums  Family Motor Coach Association    Newbie emblem placement & mounting questions
Page 1 2 

Moderators: edgray
Go
New
Find
Notify
Tools
Reply
  
-star Rating Rate It!  Login/Join 
"Winnebago Coach Forum Member"

Posted Hide Post
Clear Silicone Seal works pretty good and comes off without leaving a mark. Hold in place with tape overnight. Just don't use too much....


Robert ,N7SLD
2005 Itasca Sunova 30B/Workhorse
500 watts Solar
2005 Wrangler Unlimited Toad
ESCAPEE# 88754
FMCA # F375012
 
Posts: 161 | Location: Glendale, Arizona | Registered: January 24, 2005Reply With QuoteEdit or Delete MessageReport This Post
"Tiffin Coach Owner's Forum Member"

Picture of Jim Martin PA
Posted Hide Post
quote:
Originally posted by Robert & Kiki:
Clear Silicone Seal works pretty good and comes off without leaving a mark. Hold in place with tape overnight. Just don't use too much....


Good morning, Robert,

Thanks for the fed back.

For now I have the emblem attached the rear ladder with copper wire.

Thanks again.

Jim


Jim & Elaine Martin
'06 Allegro 32 BA (Ford)
'06 Saturn Ion 2
Roadmaster stuff / 9060 BrakeMaster
FMCA - F373167
Jim's RV Tips
 
Posts: 93 | Location: Philadelphia area | Registered: December 16, 2005Reply With QuoteEdit or Delete MessageReport This Post

Posted Hide Post
Jim,rather than use copper wire,why not try the plastic wire ties? Wouldn't that be better on your ladder?

<<<<<<<<<<<<------------Check this out...
 
Posts: 10369 | Location: Jupiter, FL | Registered: December 25, 2003Reply With QuoteEdit or Delete MessageReport This Post
"Tiffin Coach Owner's Forum Member"

Picture of Jim Martin PA
Posted Hide Post
quote:
Originally posted by rebelsbeach:
Jim,rather than use copper wire,why not try the plastic wire ties? Wouldn't that be better on your ladder?

<<<<<<<<<<<<------------Check this out...


Good point - When I put the emblem on I didn't have an heavy duty tie wraps so I used #12 copper wire.

Next time I'm in Home Depot I will pick up some tie wraps.

Thanks again for the suggestion

Jim


Jim & Elaine Martin
'06 Allegro 32 BA (Ford)
'06 Saturn Ion 2
Roadmaster stuff / 9060 BrakeMaster
FMCA - F373167
Jim's RV Tips
 
Posts: 93 | Location: Philadelphia area | Registered: December 16, 2005Reply With QuoteEdit or Delete MessageReport This Post

Picture of Paulin
Posted Hide Post
We too were concerned about mounting the emblems and finaly bought a pair of ladder brackets from Kiely Mold Co. at www.kielymold.com. They were only $12 and are recessed so that the ladder is usable without removing the emblem. We will just display the front emblem in the windshield.


Paulin
2007 Jayco Seneca HD 34SS Duramax
VUE V6 toad
"Monty", "Maggie" & "Murphy" the mighty Shih-Tzus
FMCA F375077
 
Posts: 383 | Location: No. CA | Registered: September 03, 2003Reply With QuoteEdit or Delete MessageReport This Post

Posted Hide Post
Bluewind, if you push the FMCA plate all the way up to the bottom of the next higher rung,there is more than enough room for your boot to get to the step....

I used my second FMCA plate for the iRV2 sticker,just turned the plate over to the smooth side.

<<<<<<<<<<<------------------------LIKE THIS

Don't have an iRV2 sticker?

That's no problem either!!

Send me a PM with your address and one will be one the way.
 
Posts: 10369 | Location: Jupiter, FL | Registered: December 25, 2003Reply With QuoteEdit or Delete MessageReport This Post

Picture of Paulin
Posted Hide Post
Woops! Sorry That Kiley Mold Co. website was mis-spelled. It should have been www.kileymold.com

Paul Oboy


Paulin
2007 Jayco Seneca HD 34SS Duramax
VUE V6 toad
"Monty", "Maggie" & "Murphy" the mighty Shih-Tzus
FMCA F375077
 
Posts: 383 | Location: No. CA | Registered: September 03, 2003Reply With QuoteEdit or Delete MessageReport This Post
"Tiffin Coach Owner's Forum Member"

Picture of Jim Martin PA
Posted Hide Post
quote:
Originally posted by Bluewind:
Woops! Sorry That Kiley Mold Co. website was mis-spelled. It should have been www.kileymold.com

Paul Oboy


Hi Paul,

Thanks for the update.

The ladder brackets look great and the emblem doesn't interfere with the use of the ladder.

I just ordered a set.

Thanks again

Jim


Jim & Elaine Martin
'06 Allegro 32 BA (Ford)
'06 Saturn Ion 2
Roadmaster stuff / 9060 BrakeMaster
FMCA - F373167
Jim's RV Tips
 
Posts: 93 | Location: Philadelphia area | Registered: December 16, 2005Reply With QuoteEdit or Delete MessageReport This Post
"Newmar Owner's Forum Member"

Posted Hide Post
Bungy Balls for everything. You need at least a hundred in the coach or you aren't using them very creatively. TED


2001 DutchStar 3852 DP, NRA Member
 
Posts: 102 | Location: Ruby Creek, MI | Registered: June 12, 2001Reply With QuoteEdit or Delete MessageReport This Post
 Previous Topic | Next Topic powered by eve community Page 1 2  
 

    iRV2.com RV Forum  Hop To Forum Categories  RV LIFE STYLES  Hop To Forums  Family Motor Coach Association    Newbie emblem placement & mounting questions

© irv2.com 2008